Where do I need to install AFDDs, and what are the considerations?

Introduction

AFDDs conforming to BS EN 62606 shall (must) be provided for all single-phase AC final circuits supplying socket-outlets with a rated current not exceeding 32 A.

However, the mandating of AFDDs is restricted to four types of installations where the effects of fire may lead to a higher risk of loss of life due to the increased number of people using the space(s) and/or increased damage to the building fabric as the geometry of the building promotes the “chimney effect.”

These are:
1. Higher Risk Residential Buildings (HRRB)
2. Houses in Multiple Occupation (HMO)
3. Purpose-built student accommodation
4. Care homes

Additionally, AFDDs are recommended on all single-phase AC final circuits supplying socket-outlets not exceeding 32 A in all other premises. For example, in a residential premises, AFDDs are not mandatory however may be extremely beneficial as there is a clear lack of maintenance and aged cabling present in dwellings which are likely to produce arc faults due to their prolonged operational lifespan.

A conversation explaining that AFDDs enhance the level of protection to the installation and are recommended as per the requirements needs to occur between the contractor and the electrical duty holder. If the duty holder is not in favour of following the recommendation, this decision needs to be recorded in writing and appended to the documentation provided to the duty holder following completion of the work.

 

What is a HRRB?

A HRRB is assumed to be residential buildings over 18 m in height or in excess of six storeys, whichever is met first. The parameters can be subject to change over time, as well as in risk management procedures adopted by fire and rescue services thus current legislation should be applied.

As the Building Safety Act received royal assent after the release of BS 7671: 2018 +A2 (2022), the definition within legislation may differ from that of BS 7671. It is therefore important for designers (and installers) to note that the definition in statutory legislation always takes precedence over a British Standard. As such, it is correct to add that any building which meets the height requirements (as mentioned above) and contains at least two residential units is classified as a higher risk building in the Building Safety Act and is therefore subject to the requirements of Regulation 421.1.7.

This means that all mixed-use developments which contain two or more residential units, would also require AFDD protection on all single-phase AC final circuits supplying socket-outlets with a rated current not exceeding 32 A.

 

Impact on Projects

This is quite a significant change which levels the playing field for all contractors to include AFDD protection within their contracts / projects, particularly with the mandatory elements.

 

Some issues/considerations when using AFDDs

The size of the AFDDs may vary from manufacturer to manufacturer. Although this appears as a negative initially, it is actually quite beneficial. The variety provides designers / installers with the flexibility to use the most suitable arrangement for the installation, particularly for retrofit projects, where space is of a premium.

For example, AFDDs can come as individual monitoring units that can be attached to either an MCB or RCBO. They also are available as single, double, or indeed triple module, with either an MCB, RCD or RCBO pairing. This adaptability allows designers to select the most appropriate solution, when taking account of aspects such as breaking capacity.

Contractors also need to be aware that the status indicators for AFDDs are often different colours (depending on manufacturer), this means that solid red, amber, or green colour can indicate “normal” status. In fault conditions, the indications also differ by either being a solid amber light or a series of flashing lights, the meaning of which can only be found with reference to the manufacturers instruction label/leaflet.

Following a disconnection, the fault sequence is only repeated once, upon initial reset of the device. If the client or ordinary person performs the initial reset, the information could be lost, making fault finding difficult. However, there are a number of manufacturers who are looking to build intelligence into their devices, with one benefit being convenient recall/ history.

 

In summary

AFDDs are mandated on single phase AC final circuits supplying socket outlets with a rated current not exceeding 32 A but only if this circuit is contained within one of the four installation types mentioned previously.

For all other locations (and circuit types), AFDDs are recommended, however the choice is made by the electrical duty holder of the respective installation with input from the electrical contractor (as the skilled person).

Recommendations within BS 7671 should be adhered to, as they have been identified as options which are particularly suitable to meet the requirements. This doesn’t exclude other options, but it does mean that contractors must demonstrate how the requirement is being met.

Finally, there are a few nuances associated with each AFDD manufacturer in terms of the size of devices and indicator lights which may vary in hue. This flexibility is actually welcome however does require particular attention be paid to the manufacturer’s instructions/literature.

Related Posts

Type AC RCDs and the effects of DC leakage current

Type AC RCDs and the effects of DC leakage current

Type AC RCDs have been the default standard for decades in the UK, however due to the increased number of electronic components, accessories and equipment in use which effectively manipulate wave and current forms, there have been issues identified with DC leakage. In...